...What to expect...

1.0...3rd gen RX-7 / STD Carbureted SB Chevy V-8...

...Preparations...

Selling Your Stock Engine/Turbos/Trans

Tools Required & Recommended Work Area

Draining / Evacuating Your AC System

Pressure Washing The Engine Compartment

Jacking & Supporting Your RX-7

What To Squirt W/ Penetrating Oil

Disconnecting The Battery

Draining Your Cooling System

Removing Your Hood

Shifter & Boot Removal

Disconnecting The Clutch Master Cylinder

Tagging The Electrical System

Exhaust & Driveline Removal

Prepping The Engine/Trans For Removal

Removing The Power Plant Frame (PPF)

Removing The Engine/Trans

What To Save Off Of The Engine/Trans

Removing Un-needed Underhood Wiring & Misc.

Steering Rack Preparations

Removing The Stock Rotary Engine Subframe

Pre-Assembly Cleaning / Detailing Of The Engine Compartment

...Granny's Subframe Installation...

Installing The Steering Rack

Re-Assembling The Front Suspension

...Engine Preparations...

Removing Un-needed Parts & Accessories

Prevenitive Maintenence

Verifing The Accuracy Of Your V-8's TDC Indicator

Installing The Distributorless Oil Pump Drive

Modifing, Checking, & Re-installing The Oil Pan

Installing The Oil Cooler Adapter

Installing The RX-7's Oil Pressure Gauge Sending Unit

...Transmission Preparations...

Prevenitive Maintenence

...Engine / Transmission Installation...

Pre-Installation Cleaning / Detailing

Rigging Engine/Trans For Installation

...Transmission Crossmember / Torque Arm Anchor Installation...

Transmission Crossmember Installation

Torque Arm Anchor Bracket Installation

...Torque Arm Installation...

Installing Torque Arm / Differential Adapter Brackets

Installing / Pre-Adjusting The Torque Arm

...Checking Drivetrain Alignment...

...Connecting The Reverse Lite Switch...

...Driveline Modification...

Determining Proper Length

Driveline Modification Choices

Driveline Installation & Clearances To Check

...Exhaust Manifold / Header Installation...

What Are The Choices?

...Clutch Master / Slave Cylinder Installation...

Master Cylinder

Slave Cylinder

Hose Routing & Bleeding

...Oil Cooler Plumbing...

Types Of Hoses & Fittings

Adapter Fittings For Your RX-7's Oil Cooler

Routing / Supporting The Hoses

Low Oil Level Sensor Wiring Modifications

...Water Pump & Accessory Drive Mounting / Pulleys...

Installing The Short Water Pump

Proper Heater Core Plumbing / Fittings

Accessory Drive Pulley Choices & Installation

...Starter / Alternator Wiring...

Starter Wiring

Alternator Wiring

...Fuel System Plumbing & Wiring...

Theory & Plumbing Of A Fuel Loop

Locating & Re-wiring The RX-7's Fuel Pump Control Relay

Installing A Fuel Pressure Regulator

...Throttle Cable...

Adapting The Chevy's Cable

...Cooling System Plumbing, Temp Sender & Electric Fan Control...

Proper Plumbing

Temp Sender Location & Installation

Fan Thermostat Installation & Wiring

...Ignition System...

Ignition Choices & Recommendations

Electromotive DIS

...Speedometer Interface Installation...

Mounting & Wiring

Calibration

...Tachometer Interface Installation...

Re-Cal OR Interface?

Re-Cal

Interface Wiring

...Variable Assist Steering Wiring...

Locating The Wires

...Battery Relocation...

Parts Recommended & Wiring Considerations

Re-connecting The Battery To The RX-7's Harness

...Installing Your Hood & Checking Clearances...

...Adjusting Your Fuel Pressure...

...Starting Your Engine...

...Exhaust System Misc...

...A/C Hoses & Recharge...

...4 Wheel Alignment...


2.0...3rd gen RX-7 / TBI SB Chevy V-8...

3.0...3rd gen RX-7 / TPI SB Chevy V-8...

4.0...3rd gen RX-7 / LT1 SB Chevy V-8...

5.0...3rd gen RX-7 / LS1 SB Chevy V-8...

6.0......

7.0......

8.0......

9.0......

10.0......


back to Granny's 1st & 2nd gen RX-7 conversion info


back to 3rd gen RX-7 conversion mainpage